This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm whether you accept or reject these cookies being set.

A cookie will be stored in your browser regardless of choice to prevent you being asked this question again. You will be able to change your cookie settings at any time using the link in the footer.

Sentora Err : You are speaking plain HTTP to an SSL-enabled server port
#1
Sentora Err : You are speaking plain HTTP to an SSL-enabled server port
Hi All,

I am new at forum, I was using Sentora without issues , unless we needed SSL enabled:
I followed 'http://docs.sentora.org/?node=102' tutorial for lets encrypt and used 'certbot' to install.

Everything was fine, but I missed a step:
 
Step 1. (I missed)
Changing Sentora port:

On Sentora Panel go to Admin -> Sentora Config -> Sentora Apache Port change to 443 and Save

and performed next step:

Step 2. 
Adding a Custom Entry to the Sentora Virtual Host

On Sentora Panel go to Admin -> Module Admin -> Apache Config > Global Sentora Entry



Is there a way to perform the missed step (to change Sentora config to 443) from command line? all the sites under hosting are effected due to the issue. Undecided

Sentora login is giving below error:

Your browser sent a request that this server could not understand.
Reason: You're speaking plain HTTP to an SSL-enabled server port.
Instead use the HTTPS scheme to access this URL, please.

 I can see and confirm that redirect is happening to port 443

PS* in /etc/sentora/configs/apache/jttpd-vhosts.config is reflecting step 2 changes.
Reply
Thanks given by:
#2
RE: Sentora Err : You are speaking plain HTTP to an SSL-enabled server port
(01-16-2019, 05:54 AM)rockford Wrote: Hi All,

I am new at forum, I was using Sentora without issues , unless we needed SSL enabled:
I followed 'http://docs.sentora.org/?node=102' tutorial for lets encrypt and used 'certbot' to install.

Everything was fine, but I missed a step:
 
Step 1. (I missed)
Changing Sentora port:

On Sentora Panel go to Admin -> Sentora Config -> Sentora Apache Port change to 443 and Save

and performed next step:

Step 2. 
Adding a Custom Entry to the Sentora Virtual Host

On Sentora Panel go to Admin -> Module Admin -> Apache Config > Global Sentora Entry



Is there a way to perform the missed step (to change Sentora config to 443) from command line? all the sites under hosting are effected due to the issue. Undecided

Sentora login is giving below error:

Your browser sent a request that this server could not understand.
Reason: You're speaking plain HTTP to an SSL-enabled server port.
Instead use the HTTPS scheme to access this URL, please.

 I can see and confirm that redirect is happening to port 443

PS* in /etc/sentora/configs/apache/jttpd-vhosts.config is reflecting step 2 changes.

There are two ways that I can think of.

One is to wait until the daemon has just run, then quickly edit the appropriate apache config file, save it and restart apache, which will make Sentora work, and then change the port setting as you should have done in the config... all within 5 minutes without the daemon running.

The other is to change the settings manually using mysql commands, then wait until the daemon runs.

Although the first might take a few attempts - because the daemon might run whilst you're making the changes that will allow you to get back into Sentora - but that shouldn't be a problem. The reason I'm not recommending using a mysql command is because I'm not 100% without checking that the daemon will pick up the change just by changing the value in mysql - there may need to be another flag changed too to trigger the daemon to then use the value you've changed.

So, as quickly as possible - to beat that daemon! - do this:

(Note that I'm using CentOS so you might have to adjust paths and commands for your server)

Edit the vhosts file:


Code:
vi /etc/sentora/configs/apache/httpd-vhosts.conf


Change the line near the top (press "i" to edit the file):


Code:
Listen 80


to:


Code:
Listen 443


unless there's another line near it that already lists port 443.

A couple of lines below that, change:


Code:
<VirtualHost *:80>


to:


Code:
<VirtualHost *:443>


Now save (ESC and type ":wq" then press enter).

Restart Apache:


Code:
systemctl restart httpd.service


Now go to your control panel with HTTPS, log in and change that config setting you missed and get it saved as quickly as you can!

If it doesn't seem to work, give it another try from the top as the daemon may have beaten you to it and changed your config back to port 80 - but I don't think the daemon will actually mess it up - again because the appropriate flag was not set that tells the daemon "there's a setting to update in the apache vhost file".

Let us know how it goes!

Keith.
Reply
Thanks given by:
#3
RE: Sentora Err : You are speaking plain HTTP to an SSL-enabled server port
It Did not worked for me, but I resolved the problem. Your configurations gave me the confidence that I am looking in right https config file.

I simply removed SSL related key information I did in step two as mentioned in my first message.

Restarted apache2 ( sudo service apache2 restart) and voila, my panel was back on port 80. I followed rest of the tutorial in order and now SSL is up and running.

Thank you for the support
Reply
Thanks given by:


Possibly Related Threads…
Thread Author Replies Views Last Post
Is Sentora dead? rajeevrrs 2 4 ,035 12-17-2022, 09:20 AM
Last Post: TGates
Sentora debug and error files johnnyp 0 1 ,620 10-27-2022, 06:16 PM
Last Post: johnnyp
Transfer Account to another Sentora BenI 1 3 ,397 07-21-2022, 07:19 PM
Last Post: Nigel

Forum Jump:


Users browsing this thread: 1 Guest(s)